Monday, July 29, 2013

Biulding Nissan GT-R R35 Toy (Step by Step

Step 1 : Body and Interior
Correct the Body

Each parts fit perfectly. They are jointed with dowels like a snap fit kit.(Of course an adhesive is necessary.)






  Trunk lid part have the bumps a little. I made them a uniform surface with sandpaper.











Painting the Body

Painted the body red. The paint is GSI Creos new color GX3 Hermann Red.










Dashboard
I painted the dashboard. It is appointed only one color of black in instruction. However, I painted five colors to express a difference of the materials.










  Masked and airbrushed the metal frames.












  Applied the meters decal. However, the size of meters of decal do not fit with the mold. I planed the mold with sandpaper, and applied the decal.










 The multi function display is not printed on the decal of Fujimi GT-R. I used it from the decal of Tamiya GT-R.

The dashboard. was completed.








Front Seat and Inner of Door
  I reproduced the feel of suede and cloth by sandblasted the dark surface primer with an airbrush.










  Front seats are two-tone color of the red and black. It is the special color for GT-R black edition.











  I used ten colors for the inner of door to reproduced the difference of materials.











  Inner door knob and switch panel.












  Rear Seat and Floor Panel
  Replicated the feel of floor panel by sandblasted the dark surface primer with an airbrush.











  Masked and airbrushed the metal plate and frames of transmission tunnel.











Floor Carpet
Replicated the floor carpets of sandpaper. They are special equipment for GT-R.











  Replicated the GT-R emblem on the carpet too.












Interior was completed
Step 2 : Chassis and Body
      Painting the Chassis 
The chassis of Fujimi 1/24 GT-R is more detailed than the Tamiya and Aoshima products. But it is hard to paint because the exhaust system and powertrain are not separated chassis.

 







Masked and airbrushed the exhaust system and powertrain. It was very very hard work...











 Painting work is finished.












Brakes System and Suspension System
The brake disk is constructed of two parts, and replicated the ventilation system. Brake caliper is separated with brake disk, and the wheel turns with it same as real car.









  Assembled the front suspension system.












  Assembled the rear suspension system and exhaust system.











  Applied the carbon decal from Modelers to the rear bottom cowling, and coated the clear paint.











  Replicated the dark chrome wheel color by coated smoke paint on the silver paint. The Nissan logo of the center cap is not printed on decal. I applied the decal of the Tamiya GT-R.









  As for the tire, Bridgestone POTENZA RE 701R is Replicated.











Panted the Body 2

Coated the urethane clear paint on the red paint, and polishing with a compound after harden. It became well-polished body!










  Masked and airbrushed the pillars and front grill etc...











  Painted the carbon pattern on the front grill, and put the metallic frame sticker.











  The mold of doorknob isn't sharp. I masked the outline and pained silver paint.











Windshield

   The instruction is wrong about the black frame area of windshield. I painted it unawares... OMG! The sunshade is black, too.










  I revised the mistake area. The sunshade became smoke color.











Headlight

  There are some parts of the headlight. It is more detailed than the Tamiya and Aoshima products.











 Assembled the headlight.












Emblems

  The "GT-R" emblem is the metallic sticker and only red paint in "R" logo is the decal.











  "GT-R" logo is molded to this plating part. However, it does not fit the logo decal to put on the top.










  Sandpapered the logo mold, applied decal, and coat the clear paint. I feel fine at this one.











Backside of the Body

  Put the grill mesh and radiator parts.












  The tail lights of this kit do not have reflector parts. I put aluminum tape instead.











Completed

Fujimi 1/24 GT-R is completion when the chassis is joined to the body afterward.




                                                                  Via: h3.dion.ne.jp

                                                  http://nissanskylinegt-rr35.blogspot.com/



No comments:

Post a Comment